Difference between revisions of "MicroMill"

From Digimaken wiki

 
(7 intermediate revisions by the same user not shown)
Line 12: Line 12:
[[File:StepStick.jpg]]
[[File:StepStick.jpg]]


=== CNC Shield wiring===
Connected are:
Connected are:
* Power supply on Blue screw terminal
* Power supply on Blue screw terminal
Line 20: Line 21:
* Red/Black wire to 5V/GND (between Blue screw terminal and reset)
* Red/Black wire to 5V/GND (between Blue screw terminal and reset)
* 3 stepper motors (X, Y, Z) to 4-pin connectors next to stepper drivers
* 3 stepper motors (X, Y, Z) to 4-pin connectors next to stepper drivers
=== Relay board ===
The relay board contains two relays, seperately switching '''Neutral''' and '''Live''' 220V wires to the Proxxon Spindle. Connections:
* Red wire to JD-VCC on conn1
* Yellow wire to VCC on conn1
* GND on conn1 is not connected
* GND to GND on conn2
* IN1, IN2, VCC on conn2 are not connected
=== Power supply ===
The power supply is Mean Well IRM-30-12ST (12V / 2.5A)


==Connecting a Probe==
==Connecting a Probe==
Line 39: Line 51:
   
   
  https://github.com/grbl/grbl/issues/464
  https://github.com/grbl/grbl/issues/464
'''Arduino pin A5 is available as "SCL" on the 8-pin breakout, two pins further is GND, so I attached a 3-pin connector here.'''
To connect a probe, I most likely need to change the GRBL image on the Arduino (probing not enabled?). First I need to find out about the current setttings, using
https://github.com/gnea/grbl/wiki/Grbl-v1.1-Commands
==ChiliPeppr==
http://chilipeppr.com/jpadie

Latest revision as of 11:24, 2 January 2018

MicroMill.jpg

The MicroMill is a 2017 Kickstarter project to promote a small desktop cnc milling machine.

Electronics

The MicroMill is driven by an Arduino UNO (clone) with a Protoneer CNC shield from Protoneer (Ebay). The board is equipped with 3 Stepstick stepper drivers. Only the Z-axis driver has a cooler installed.

CncShield.jpg StepStick.jpg

CNC Shield wiring

Connected are:

  • Power supply on Blue screw terminal
  • Green button to Resume
  • Red button to Abort
  • Door to E-Stop
  • Yellow wire to SpnEn (single wire on white pin)
  • Red/Black wire to 5V/GND (between Blue screw terminal and reset)
  • 3 stepper motors (X, Y, Z) to 4-pin connectors next to stepper drivers

Relay board

The relay board contains two relays, seperately switching Neutral and Live 220V wires to the Proxxon Spindle. Connections:

  • Red wire to JD-VCC on conn1
  • Yellow wire to VCC on conn1
  • GND on conn1 is not connected
  • GND to GND on conn2
  • IN1, IN2, VCC on conn2 are not connected

Power supply

The power supply is Mean Well IRM-30-12ST (12V / 2.5A)

Connecting a Probe

According to the GRBL documentation, a probe should be connected to Arduino pin A5:

The G38.2 straight probe and G43.1/49 tool offset g-code commands are now supported. 
A simple probe switch must be connected to the Uno analog pin 5 (normally-open to 
ground). Grbl will report the probe position back to the user when the probing cycle 
detects a pin state change. (https://github.com/grbl/grbl/blob/edge/README.md).
Whatever probe you design should be able to handle some over travel, the Z movement 
likely won't stop immediately. Some sort of spring arrangement would do.
So the probe is anything that will take pin A5 to ground when it touches your object. 
The probe position is relative to machine 0. A typical porbe command might be 
G38.2 X20 Y15 Z-100 (in mm mode). You should set a slow feed rate , e.g. F20 
(20mm/min). The G38 will move to X and Y, then Z axis will lower to -100 until the 
probe makes contact with your object, at which time movement stops. Grbl will 
report the machine position of the probe touch.

https://github.com/grbl/grbl/issues/464

Arduino pin A5 is available as "SCL" on the 8-pin breakout, two pins further is GND, so I attached a 3-pin connector here.

To connect a probe, I most likely need to change the GRBL image on the Arduino (probing not enabled?). First I need to find out about the current setttings, using https://github.com/gnea/grbl/wiki/Grbl-v1.1-Commands

ChiliPeppr

http://chilipeppr.com/jpadie